Loonie PerksDeals for Canada
BlogSearch
Product guide

Polymaker PolySmooth PVB Filament, 1.75 mm, 750 g, Beige

Polymaker PolySmooth is a beige PVB filament for 3D printing, with a listing claim that prints can be smoothed using IPA alcohol. Its moisture sensitivity makes dry storage and careful handling important considerations alongside its surface-finishing potential.

At a glance

  • PVB filament described as printing with conditions similar to PLA.
  • The listing describes smoothing the print surface with IPA alcohol, with the surface finish dependent on post-processing.
  • A drybox is recommended because the filament is described as absorbing moisture more readily than regular PLA.
Price
$19.99Save 33%

Reference price: $29.99

Price checked: Nov 19, 2026

View offer

Often bought together

Pros and cons

Pros

  • Alcohol smoothing offers a way to reduce visible layer lines after printing, according to the listing.
  • The listed beige colour and 1.75 mm diameter make the intended filament format clear.

Cons

  • Moisture management adds a storage and printing requirement compared with a less moisture-sensitive filament.

Technical specifications

13 specifications
Identity
BrandPolymaker
ModelPJ01012
Dimensions and installation
Dimensions listed16 x 20 x 6 cm; 750 g
Weight listed750 g
Filament diameter1.75 millimeters
Colour113 - 1.75mm Beige (Hex Code: #Ebd591)
Materials and protection
Material listedPolyvinyl Butyral
Printing and finishing
Suggested nozzle temperature200˚C
Suggested bed temperature50˚C
Suggested speed60mm/s
Listed print temperature range190-220˚C
Listed print speed range40-60mm/s
Alcohol smoothingAlcohol Smoothable

What to know before buying

Listing details to confirm

The listing gives different print guidance: one section specifies a 200˚C nozzle, 50˚C bed and 60mm/s, while another gives 190-220˚C and 40-60mm/s. Treat these as listing details to confirm against the material and printer setup. It also alternates between IPA spray finishing and smoothing with the Polysher, so confirm the intended post-processing method. Drybox use is recommended, and the listing warns not to release the filament tip to avoid tangles.

Who is it for?

A good fit for

  • Makers seeking beige PVB filament with an alcohol-smoothing post-processing option.
  • Users prepared to manage moisture-sensitive filament and tune print settings for their setup.

Less suited to

  • Buyers who want filament that requires no special moisture-control practices.
  • Users looking for a confirmed single print profile or a guaranteed layer-line-free result without post-processing.
Polymaker PolySmooth PVB Filament, 1.75 mm, 750 g, Beige · photo 2
Additional product photo 2

Customer reviews on Amazon

4.7 / 5 · 5 ratings
  • 5 stars67%67%
  • 4 stars33%33%
  • 3 stars0%0%
  • 2 stars0%0%
  • 1 star0%0%

The listing provides aggregate ratings but no customer comments or aspect-specific feedback. Those figures alone do not establish which features buyers liked or any reasons for their ratings, so they offer limited guidance on print consistency, moisture handling or finishing results.

Frequently asked questions

What material is this filament?

The listing identifies it as Polyvinyl Butyral, or PVB.

How does the listing say prints can be smoothed?

It describes IPA alcohol smoothing and also references the Polysher. The listing does not consistently specify one method, so check which process you intend to use.

Does this filament need moisture control?

The listing says it absorbs moisture more readily than regular PLA and recommends using a drybox.

Which print settings should I use?

The listing gives both a specific suggestion of 200˚C nozzle, 50˚C bed and 60mm/s, and broader ranges of 190-220˚C and 40-60mm/s. Confirm suitable settings for your printer and filament.

Polymaker PolySmooth PVB Filament, 1.75 mm, 750 g, Beige · photo 3
Additional product photo 3

Alternative options

Product details in Markdown